Model: | T8 |
---|---|
Brand: | Syhdee |
Origin: | Made In China |
Category: | Consumer Electronics & Lighting / Lighting / LED Lighting |
Label: | led tube , led tube light , t8 led tube 18w |
Price: |
US $3.9
/ pc
|
Min. Order: | 500 pc |
General Introduction
This high Lumen Design G5 pins T8 LED lamp body LED tube uses SMD LED2835 as light source and there are 600mm(2 feet), 900mm(3 feet), 1200mm(4 feet), 1500mm(5 feet) available.With longer lifespan(>50,000hours), higher brightness and less toxic substance, it can be widely used to replace the traditional fluorescent tube lights. This type of Design G5 pins T8 LED lamp body LED Tube adopts the standard G5 socket and works with AC100-240V voltage input and DC72-80V voltage output. It is RoHS approved.
LED Tube Parameters
Product |
New Disign T8 LED Tube Lighting G5 Pin T8 LED Lamp 19W 4ft Tube Lights |
|
Optical Parameters |
Light Source |
SMD LED2835 |
Luminous Flux(lm) |
1250 |
|
CCT(K) |
6000-6500 |
|
CRI(Ra) |
70 |
|
Beam Angle |
120°-160° |
|
Light Attenuation ratio (%) |
Less than 10% in 3 years |
|
LED Quantity |
100 |
|
Electrical Parameters |
Input Voltage(V) |
AC100-240V |
Frequency(Hz) |
50/60HZ |
|
Output Voltage(V) |
DC72-80V |
|
Total Power(W) |
13 |
|
Power Factor |
>0.9 |
|
Lifespan (Hrs) |
>50,000 |
|
Dielectric Voltage Withstand Test |
3750Vac/60s |
|
Structural Parameters |
Material |
Aluminum housing &PC cover |
Size(mm) |
Φ26×1200 |
|
Length(mm) |
1200 |
|
Net Weight(g) |
320 |
|
Integrated Parameters |
Operating Temperature |
-10°-40° |
Storage Humidity |
-40°-85° |
|
Safety Requirement |
/ |
|
Environmental Directives |
RoHS |
T8 LED Tube Details Photo
A |
B |
_ |
Size A |
Size B |
Caps |
1148 |
1162 |
G5 |
LED Tube Application
G5 pin T8 lamp body LED tube can be applied in indoor LED lighting, places as office, school, meeting room, etc.
LED Tube Installation
G5 Pins T8 Lamp Body LED Tube Wiring Diagram:
1) Please turn off electric power before LED Tube Lights installation 2) For refitting old fluorescent lamp, with a two-side-power-input LED tube, please re-connect your wire as the following diagram
3) For diagram A1 loop with inductive ballast & starter, after removing the starter, LED tube can be installed directly into the G13 base. Then LED tube light is ready to work. And the loop has been changed from A1 to A2.
Note: You can just keep the inductive ballast as it was. However, it’ll consumer some power. For saving energy, it’s still s ested to cut it out if your labor cost is not so high.
4) For diagram B1 loop with electronic ballast , please remove the electronic ballast first. Then connect L and N to the two sockets of the G13 base separately. Now your LED tube light is ready to be turned on. And the loop has been changed into the one showed in diagram B2. |
Shenzhen Syhdee Co., Ltd. | |
---|---|
Country/Region: | Guang Dong - China |
Business Nature: | Manufacturer |
Phone: | 13316918221 |
Contact: | Maggie (Marketing) |
Last Online: | 15 Dec, 2015 |