16串主動均衡鋰電池管理系統

產品描述

APHEV-BMS-01-16-01

1 Introduction

The BMS module of 16 series adopts high precision analog front-end chip and

high performance 32 bits MCU, superior performance to extend battery life, and

ensure the batteries for safety.

2 Composition of System

Main features: high precision signal acquisition module，high precision SOC

estimation module, active energy transfer balance mode，the cell information

storage module, the cell protection module (overcharge protection, over

discharge protection, high and low temperature of cell protection), optional

LCD display module.

3 Package Information

The package is labeled with five descriptors

4 Features

4.1 Active balancing energy transfer type, high current is 1.5 A.

4.2 Optional battery balance modes: Automatic balance or Force balance.

4.3 Module reserved RS485 bus interface can be scaled to 32 cell, 48 cell and more

than thousands of cells.

4.4 Include a 4G SD card, can store 10 years for battery information.

Item	Parameter
Size	21012037.5mm
Application	16 cells LiFePO4 batteries or 16 cells Lithium polymer batteries
Working Range	36 – 60V
Sleep mode power current	< 3mA
Normal Operating current	< 20mA
Monomer battery voltage measurement error	< 0.002 V
Monomer battery balanced current(Active balancing energy transfer mode)	≥1.2A Nominal 1.5 A
Temperature measurement error	±2°C
Monomer battery over voltage protection	3.55V
Monomer battery low voltage protection	2.75V
Batteries over temperature protection	65℃±2℃
Batteries low temperature protection	≤3℃
Batteries low-voltage protection	36±2 V
Low voltage protection after the recovery voltage	42±2V
SOC measurement error	≤5%
Battery information storage	＞10years

5 Electrical Parameters

Monitoring	3.2 inch touch screen LCD
Communication	CAN 2.0
Extension	RS485 extension other modules
Force Balance Mode Balancing switch to position “I”.	Balance when High - Low difference is above 10mV. Stop balancing when the delta is 10mV
Automatic Balance Mode (Default) switch position “0”	(i) Balancing is always on: Monomer battery differences over 60 mV starts automatic balancing to 60mV. (ii) Balance every 15 days, Balance when High - Low difference over 60mV. Stop balancing when the delta is 10mV or Day 15+1
BMS Module circuit protection	Balancing modes will be turned off when the module temperature reaches 65°C, Balancing will restart when the temperature is below 45°C

Single cell drops below 2. 75V

Red LED flashes and suspends discharging

Single cell exceeds 3.55V

Red LED flashes and suspends charging

Battery Temperature > 70°C

Red LED flashes and suspends discharging

and charging

LED Indicators

6 Schematic Diagram and Definition of BMS Module

Interface

6.1 Front panel interface

6.2 Anderson connection Interface.

Reset Restart measuring functions

3.2 inch LCD display module key

Reset Re-start the display, re-calibrate touch screen

Interface diagram
BMS16 front panel（look from the outlet end） Note : P1 and P2 are configured as described in the table below
Pin Number	Function	Pin Number	Function
1	BAT-1－	11	18B20 1VDD
2	BAT-2－	12	DQ
3	BAT-3－	13	GND
4	BAT-4－	14	18B20 2VDD
5	BAT-5－	15	DQ
6	BAT-6－	15	DQ
7	BAT-7－	16	GND
8	BAT-8－		－: Cell negative pole

6.3 Interface Socket Definitions

BMS Display Monitor - The definition of CAN BUS and 5V power supply

Pin Number	Function
1	5V
2	CANH
3	CANL
4	GND

9	BAT-8＋	NOTE	＋: Cell positive pole
10	NONE

BMS Control Interface
BMS16 front panel（view from the outlet）
Pin Number	Function
1	Over discharge protection(relay disconnected normally, contact closure condition: 0.5A/24V)
2	Detect input current（input: 0-5V, range: 0-150A）
3	Over discharge protection（relay disconnected normally, contact closure condition: 0.5A/24V）
4	GND
5	GND
6	GND
7	Detect output current（input: 0-5V, range: 0-30A）