The Waterproofing Systems Specialist
HESHENG® HS-08
One Component Water Based Acrylic Nano Elastomeric Waterproofing
Coating
INTRODUCTION
HS-08 One Component Water Based Acrylic Nano Elastomeric Waterproofing Coating imported the
crystallization of international advanced technology, main raw material is imported acrylic latex, it’s a one
component, water based, non-solvent, non-toxic, non-polluting waterproofing coating refined by plasticizers,
additives and fillings etc.. Color is optional by mixing pigments, it’s widely applied in all kinds of waterproofing
systems, it’s a ideal and high class environmental friendly waterproofing coating.
ADVANTAGE
a.Applied on many kinds of wet and dry substrate.
b.Coat(layer) is tough, high elastomeric, high strength, good waterproofing and durability.
c.One component application, color is optional by mixing pigment.
d.Applied on vertical, slope and top substrate, no liquid flow.
e.Non-toxic, non-VOC, non-polluting, easy application, short project period.
f.Excellent resistance to UV, weather, it’s applied under exposure.
APPLICATION RANGE
a. All kinds of moisturizing and waterproofing coat(layer) such as wet or dry sand, mortar, concrete, metal,
wood, hard plastic, glass, gypsum board, cystosepiment, bitumen, rubber, SBS, APP, polyurethane etc..
b. All kinds of waterproofing or leakage for new or old buildings and structures(such as waterproofing on
roofing, toilet, underground, tunnel, bridge or leakage on window sill and edge, flower box, sanitary ware etc).
c. Bonding or sealing materials and decorative coating for exterior wall.
MAIN TECHNICAL INDEX
Executive Standard: JC/T864-2000
Item
Index
Type Ⅰ Type Ⅱ
Solid Content % ≥65
Drying Time
Tack-free h ≤4
Curing h ≤8
Tensile Strength Mpa ≥0.1 ≥1.5
Breaking Elongation % ≥300
Impermeability 0.3Mpa，30min No Seepage
Low Temp. Flexibility Ф10mm Stick -10℃ No Crack -20℃ No Crack
APPLICATION METHOD
Brush coating on the surface with roll brushes or squeegee, while finding coating in much dense(viscous), it
would be diluted by mixing with water, it will forms integral waterproofing membrane after coating curing.
Brush 3 - 4 coats(layers), brush next coat(layer) after last coat(layer) is curing.
APPLICATION REQUEST
Substrate request: substrate must be level, solid, clean, free of water and leakage, while finding uneven and
crack, we must level it, and plug the leaking place, repair convex corner to round corner.
Three application cases for your choice: according to different waterproofing systems, we should choose
relative cases. Above application range, coat(layer) structure, requested accessory, coating mixing ratio and
consumption show as following table:
Case 1:
Top Coat(Layer)（Coating consumed 0.9kg/m2）
Low Coat(Layer)（Coating consumed 0.9kg/m2）
Bottom Coat(Layer) （Coating ：Water=1：1 Coating consumed 0.3kg/m2）
Substrate
Total Consumption: 2.1Kg/m2 Coating Thickness: 1.2mm
Application Range: Common Building Waterproofing
Case 2:
Top Coat(Layer)（Coating consumed 0.9kg/m2）
Middle Coat(Layer)（Coating consumed 0.9kg/m2）
Low Coat(Layer)（Coating consumed 0.9kg/m2）
Bottom Coat(Layer)（Coating：Water=1：1 Coating consumed 0.3kg/m2）
Substrate
Total Consumption: 3.0Kg/m2 Coating Thickness: 1.8mm
Application Range: More Important Building Waterproofing
Case 3:
Top Coat(Layer)（Coating consumed 0.9kg/m2）
Middle Coat(Layer)（Coating consumed 0.9kg/m2）
Non Woven Fabrics Coat(Layer) ~ ~ ~ ~ ~ ~ ~ ~ ~~ ~ ~ ~ ~
Low Coat(Layer)（Coating consumed 0.9kg/m2）
Bottom Coat(Layer)（Coating：Water=1：1 Coating consumed 0.3kg/m2）
Substrate
Total Consumption: 3.0Kg/m2 Coating Thickness: 2mm
Application Range: Reinforced Building Waterproofing and Building Special Shape Place Waterproofing
(such as parapet wall, gutter inlet and convex corner etc.)
Non-woven fabrics material: polyester Unit Weight: 35-60g/m Thickness:0.25-0.45mm
Brush coating with roll brush or squeegees, brush coat(layer) by coat(layer) according to scheduled case,
brush next coat(layer) before last coat(layer) is tack-free and not curing. Low temperature, high humidity, bad
ventilation will delay curing time, otherwise, in opposite. For case 3, we must continue to apply between low
coat(layer), non woven fabric coat(layer) and middle coat(layer), no interval, which makes it form a integral
with coat(layer).
While brushing evenly, no part deposition, bottom coat(layer) need to be brushed in several times, which
ensure no bubble between coating and substrate, bonding completely. While brushing protective coat(layer),
we can sprinkle coarse sand on last coat(layer) after brushed, and brush a cement mortar protective
coat(layer) after curing.
NOTE
a. Application can not below 4℃ or under rain, as well under special wet or free of ventilated environment, or
delay forming membrane.
b. No need to add water while application, close bucket cover after run out.
c. Make leakage proof test in 4 - 5 days after waterproofing systems finished, that is 2 hours after rain or
continuous water pouring, if possible, we can store water 24 hours, if no leakage, it passed. (Under bad air
circulation, wet, long curing environment, leakage proof test time will be delayed)
d. It must be sealed and stored above 0℃ shade place, close bucket cover, avoid sun exposure, shelf life is
1 year.
PACKAGE
25kg/bucket
50kg/bucket
53 US Gal/Bucket
Foshan Shunde Hesheng Chemical Industry Co., Ltd.
Web: www.he-sheng.com.cn/en/
Tel.:+86 757 22904888 Fax.:+86 757 22904999
Headquarter Addr.:No.11-1-2, Fu An Industrial Area, Leliu, Shunde, Foshan City, Guangdong Province, China
Sub-factory Addr.:NO.10 Fuyuan Rd.,Rongbian, Rongui, Shunde, Foshan City, Guangdong Province, China