Addition Molding Silicone

Model:	M610 #
Brand:	Wuhan xilikang silicone
Origin:	Made In China
Category:	Chemicals / Rubber Materials
Label:	silicone , silicone rubber , Addition Silicone
Price:	US $9 / KG
Min. Order:	25 KG

Inquire Now

Product Description

Description

Addition-cured silicone mold
Model	Appearance	Hardness (Shore A)	Tear-strength (kgf/cm)	Tensile-strength (kgf/cm2)	Elongation（%)	Viscosity (cp)	Working Time (mins)	Demould Time (hrs)	Mixing Ratio (%)
Y600	Translucent	0±2	≈2	≈15	≈ 400	≈2000	50-60	4-6	1 : 1
Y605	Translucent	5±2	≈8	≈25	≈500	≈2500	30-40	4-6	1 : 1
Y610	Translucent	10±2	≈12	≈30	≈550	≈4000	30-40	4-6	1 : 1
Y615	Translucent	15±2	≈14	≈45	≈550	≈5000	30-40	3-5	1 : 1
Y620	Translucent	20±2	≈20	≈50	≈450	≈6000	20-30	3-5	1 : 1
Y625	Translucent	25±2	≈13	≈55	≈500	≈7000	20-30	3-5	1 : 1
Y630	Translucent	30±2	≈13	≈65	≈450	≈8000	20-30	3-5	1 : 1 or 10 :1
Y635	Translucent	35±2	≈13	≈70	≈450	≈8000	20-30	3-5	1 : 1 or 10 :1
Y640	Translucent	40±2	≈13	≈80	≈310	≈9000	20-30	3-5	1 : 1 or 10 :1
Y650	Translucent	50±2	≈10	≈70	≈150	≈12000	20-30	3-5	1 : 1 or 10 :1
Y655	Translucent	55±2	≈9	≈60	≈110	≈20000	20-30	by heating	1 : 1 or 10 :1
Y660	Translucent	60±2	≈8	≈50	≈70	≈30000	20-30	by heating	1 : 1 or 10 :1
E665	Translucent	65±2	≈7	≈40	≈70	≈30000	20-30	by heating	1 : 1 or 10 :1

HY- E6# addition molding silicone is generally named two-components silicone rubber, Part A is a flowable liquid, part B is the curing agent. It features an exceptional fluidity and good operability. The mixing ratio is 1:1,mainly be suitable for making masks, arms, legs, and other FDA molds application.

addition molding silicone could be mainly used for making concrete stones, precision molds, PU molds, for life casting, fabric finishing, candle molds, cake molds,seal for electronic components and solar circuit board, trademark decoration. etc.

Technique Data of HY-Y6# molding silicone

OPERRATING INSTRUCTION of HY-Y6# molding silicone:

1. Stir part A and part B with right mixing ratio evenly. And get the mixture for vacuum-pumping. (If there is no vacuumizer, you can just pour the mixture slowly from the corner so that less bubbles caused)

2. Enclose the product (the original model) with four plastic plates or wooden plates.

3. Clean your products and brush a layer of release agent(detergent or soap water) on your product.

4. Pour the mixture with correct mixing ratio into the model frame.

After about 2-4 hours, when the silicone cured, get out the original model, and there you get a finished addition cured silicone mold .

SHELF LIFE: Twelve (12) months from date of shipment when stored at 24℃ in original unopened packages.

PACKAGE: Packed in clean 20kg/pail, 200kg/pail.