The Waterproofing System Specialist
HESHENG® HS-16(K11)
Two Component General Polymer Modified Compound Waterproofing
Coating
INTRODUCTION
HS-16 K11 Two Component General Polymer Modified Compound Waterproofing Coating made of unique formula
with high polymer emulsion and inorganic powder, its powder made of excellent quality cement, quartz and unique
high polymer. This a permeation mechanism that crystalline material migrate into concrete slab and forms
recemosum(cirsoid) crystal, isolate water molecules channel inside the structure, and it will forms an integral
compound two component waterproofing coating.
ADVANCE
1.Good flexibility, it can cover micro crack on the substrate.
2.High bonding strength, lay finishing coat(layer) after waterproofing coat(layer) is curing.
3.Resistance to water, high wearability, applied to wet substrate.
4.Environmental friendly, non-toxic, applied to drinking water pool.
APPLICATION RANGE
1.All kinds of waterproofing systems on indoor or outdoor cement concrete, precast element, brick wall etc..
2.All kinds of waterproofing systems on underground car park, tunnel, well, water draining or water supplying pipe,
floor roofing, wall floor, toilet, kitchen, flower box, swimming pool and drinking water pool, roofing etc..
3.The substrates layed with stone, ceramic tile, wood flooring, wall paper and gypsum board.
MAIN TECHNICAL INDEX
Executive Standard: JC/T 984-2011 Type II
Test Item Index
Setting Time
Initial Setting min ≥45
Final Setting h ≤24
Resistance to
Permeable Pressure Mpa
Coat(Layer) Test-piece 7d ≥0.5
Tension & Pressure Strength Mpa ≥24.0
Tension & Fold Strength Mpa ≥8.0
Flexibility (Lateral deformability) mm ≥1.0
Bonding Strength Mpa
7d ≥1.0
28d ≥1.2
APPLICATION REQUEST
1.Substrate Treatment: Substrate is solid, flat, clean, free of dust, oil, hollowing and other loose things. While finding
obvious hole void and sand hole, we must level and plug it with cement mortar, repair convex corner to round corner.
2.Material Mixing: Sufficiently mix liquid with powder in 2 - 3 mins to paste without mass of powders. Run out of all
mixed paste in 1h.
(Weight ratio) liquid material : powder = 1 : 2.7.
3.Application: wetting substrate with water, brush mixed paste in crossing direction with fur brush or roll brush,
avoid leaking brushing, in general, brush more than 2 coats(layers), coat(layer) thickness keep above 1.2mm. Brush
next coat(layer) after last coat(layer) is tack-free.
4.Material Consumption: In theory, 1.0mm thickness waterproofing membrane consumed about 1.5 – 1.8kg/m2.(Total
amount after mixed liquid with powder, above consumption under flat substrate), actual consumption will be different
according to specific substrate and lose.
NOTE
1.Application temperature keeps 5 - 45 ℃.
2.We must take necessary protection for waterproofing coat(layer) before curing, includes prohibits
pedestrian, rain erosion, exposure, cold or damaged by edge item. No need to brush protective coat(layer)
after waterproofing coat(layer) is curing.
3.It should be sealed and stored above 5℃, in shade and dry place, unopened coating shelf life is 1 year.
PACKAGE
20kg/pail
Foshan Shunde Hesheng Chemical Industry Co., Ltd.
Web: www.he-sheng.com.cn/en/
Tel.:+86 757 22904888 Fax.:+86 757 22904999
Headquarter Addr.:No.11-1-2, Fu An Industrial Area, Leliu, Shunde, Foshan City, Guangdong Province, China
Sub-factory Addr.:NO.10 Fuyuan Rd.,Rongbian, Rongui, Shunde, Foshan City, Guangdong Province, China
